Paul Hoover, Owner/Winemaker
Still Waters Vineyards

Winery Equipment Testimonial:

"Upgrading your winery from 1000 cases per year to 3000 to 5000 can be a daunting task. The choices in winery equipment, capacity and price vary all over the place.  The great thing about Ryan is, having been a wine maker for years, he knows how to design things from start to finish. When I harvested my first ten tons of the year at 6:30 a.m., Ryan and his staff were there making sure everything was working correctly. I knew I had made a good decision."

Home > Winery Equipment > Wine Presses > Dhea Membrane Presses

Dhea Presses

Pneumatic Horizontal Wine Press with Central Inflating Membrane Bladder  

Dhea Membrane Bladder Press

Benefits of Central Inflating Membranes vs Traditional Bladder Presses

  • Higher Quality Yields
  • Higher Yields
  • Less Heavy Tannins
  • Faster Pressing Cycles
  • Less Oxidation, Less Browning on Whites
  • No Load Minimums

Functioning Principle

Having a Thinner Cake Leads to Several Advantages

New Technology Dhea Presses

  • Higher Yields at Much Lower Pressures
  • Higher Quality Yields
  • Less Heavy Tannins
  • Faster Pressing Cycles
  • Less Oxidation, Less Browning on Whites
  • Inert Gas Injection into the Drum
  • No Load Minimums
  • Bladder can reach the entire circumference of the Drum 
  • Even Pressures throughout the Press
  • 10 to 20 years Lifespan on the Bladder (5/16" Thick)
  • Lower Energy Consumption
  • Ability to Press Crushed Apples and Deshelled Pomegrantes

 

 

Old Technology Bladder Presses

Horizontal Nylon Bladder Presses

 

  • Lower Yields at Higher Pressures
  • Indroduction of Heavy Tannins from the skins due to high pressures needed to achieve yields 
  • Longer Pressing Cycles
  • More Lees and Fining due to having to break the Cake Multiple Times
  • More Oxidation, More Browning on Whites due to longer Pressing Cycles
  • Minimum Load Capacities for Press use and Press Efficiency
  • Thin Nylon Bladder, easier to tear and needs to be replaced more frequently (less than 1/16" thick 

 

 

5 Connected Drip Channels

The Dhea utilizes a fully closed drum. The major benefits of this is reduced oxidation and less browning of whites. Having a fully enclosed drum also allows for the winemaker to allow additional juice and skin contact time if desired. A pierced open drum is avaialbe upon request.


 

Five Drip channels are placed 360°around the inside of the drum, with an internal collector that connects the five drip channels. This allows for the optimal extraction of the juice in any of the pressing phases in any location and in the most efficient manner.

 
Patented Variable Position Pressing Phases

The Dhea comes standard with its patented variable position pressing phases: The Press legs are hydraulically driven and adjust to the phase you are performing. This system greatly increases the performance and efficiency of each of the cycles, which in turn reduces the pressing times.

Press Loading

With the press hydraulically tilted toward the tub of drain side of the drum several advantages occur. First the free run is accelerated in exiting the press. Secondly this shortens the loading times of the press, without the necessity of double or triple doors placed on the drum. This system also decreases the amount of rotations needed to fill the entire drum, again shorting the loading times and reducing the amount of lees and subsequent filtration needed in the wines.  

 

Pressure Holding & Cake Breaking

The horizontal position is used during the pressing cycle, it insures a perfect distribution of the cake 360 degrees around the drum. It also allows 100% of the internal juice channels to be utilized during the pressing cycles. Due to the decreased thickness of the cake because of the central inflating membrane, again higher yields at much lower pressures can be realized in much shorter length cycles. The number of pressing and cake breaking cycles can also be decreased.

Press Unloading

With the Press tilted towards the unloading door, the time it takes to discharge the press is greatly reduced. This allows again for fast discharge without the necessity of double or triple doors. This allows you to use the self cleaning cycle even faster.

 

 

Fully Automatic Self Cleaning

Self Cleaning Press

Tired of all the labor and time required to clean and sanitize your press? The Dhea decided that climbing into the press in order to clean and sanitize it was for old technology presses. The Dhea now has a complete self cleaning cycle so you never have to climb into the drum again. The Dhea even has a built in pump to increase the pressure of your water or sanitizing solution to insure the self cleaning gets performed properly! 

 

High Quality Components

Having the press work correctly when you need it is imperative for the successful operation of a winery producing high end wines. The Dhea realizes this and only uses the highest quality components in all their presses. The built in air compressor comes standard on all Dhea presses as well as the self breaking gear motor, pinion, crown wheel, and chain for the drum rotation.

 

Inert Gas Injection

The Dhea press comes standard with a large axial feed ball valve to avoid the crushing of the grapes prior to entering into the press. Alternatively the press can be loaded through the door if you prefer. For even more protection against oxygen exposure, an inert gas injection quick connection comes standard on the press. Now you can fill the closed press drum prior to, during and after loading the press. The inert gas can also be added while the press is in rotation. 

Pneumatic Doors Standard

The pneumatic opening and closing doors are standard on all Dhea presses. The door is placed at the end of the drum not the center for easier and more efficient loading and unloading of the grapes and must. Because of this position of the door on the drum double and triple doors are no longer required for fast filling and emptying the press. 

 

Touch Screen PLC or Manual PLC

touch screen control panelManual Control

 

 

 

 

 

 

The Dhea makes operation of your press simple and precise. The Press can be ordered with pre-set programs built into the press for whites and reds to fit most every need or purchased with a touch screen and the ability to personalize or change any of the programs. Creating your own pressing cycle programs is also very simple to perform and save to the PLC!.

Lateral Must Collecting Eaves

 

Lateral Juice collecting eaves are mounted to the frame of the press and positioned perfectly to catch 100% of your juice. They are easily removable for complete sterilization of the press.

 

Large Reversible Must Collection Tank

The Dhea comes standard with the automatic must pump controller that will turn on and off your pump as the tank fills. The Must collecting tank is reversible and the outlet for the pump can be built onto either side of the press.

 

 

Winery-Brewery-Distillation Equipment & Supplies

Showing 1-9 of 9 Results Sort by

Press, Dhea 150
Dhea HL-150 Horizontal Membrane Press

Please Call for Pricing

More Info

Press, Dhea 100
Dhea HL-100 Horizontal Membrane Press

Please Call for Pricing

More Info

Dhea HL-80 Horizontal Membrane Press
Dhea HL-80 Horizontal Membrane Press

Please Call for Pricing

More Info

Press, Dhea 50
Dhea HL-50 Horizontal Membrane Press

Please Call for Pricing

More Info

Press, Dhea 32
Dhea HL-32 Horizontal Membrane Press

Please Call for Pricing

More Info

Press, Dhea 24
Dhea HL-24 Horizontal Membrane Press

Please Call for Pricing

More Info

Press, Dhea 16
Dhea HL-16 Horizontal Membrane Press

Please Call for Pricing

More Info

Press Dhea Hoby 6
Hoby 6 Membrane Press

Please Call for Pricing

More Info

Press Dhea Hoby 10 w/PLC
Hoby 10 Membrane Press

Please Call for Pricing

More Info

Showing 1-9 of 9 Results Sort by
Your Cart Contains:

0 Item: $0.00

Please fill out the form below to sign up for our newsletter.
Copyright © 2019 The Vintner Vault | Website Development and Hosting by SMS Masterminds